Kofax Transformation Modules 7.0.0 Fix Pack 2

Release Date: June 15, 2022

© 2022 Kofax. All rights reserved.
Use is subject to license terms.

Introduction

Issues Resolved in This Fix Pack

Issues Resolved in Previous Fix Packs

Applies To

Files Included

Install This Fix Pack

Remove This Fix Pack

Introduction

You can install Kofax Transformation Modules 7.0.0.2 to resolve the issues listed below.

Note: To install Kofax Transformation Modules 7.0.0.2 successfully, an existing full installation of Kofax Transformation Modules 7.0.0 is required.

If you need to perform a full product installation, see the Kofax Transformation Modules Installation Guide for instructions.

Issues Resolved in This Fix Pack

1808372: Line breaks are missing in QR Code recognition

Binary bar code detection is now available when using the OmniPage recognition engine.

1806406: Project Builder crashing with structured exception when loading a project.

Project Builder no longer crashes with a structured exception when loading a project.

1805323: Fallback profile of RecoStar engine is not used in AZL after migration.

The fallback profile for zones is now updated correctly for the RecoStar recognition engine.

1795945: Missing Kofax.KSMS.Global.dll after upgrade from KTM 6.4.0.x to KTM 7.0

The Kofax.KSMS.Global.dll is no longer missing. The DLL version is 69.0.1850.0 which is higher than the version added in the previous fix pack.

Issues Resolved in Previous Fix Packs

Problems Resolved in Fix Pack 1

1786029: When Rotating a Multipage TIFF pages are lost

Pages in a document are no longer lost after the document is rotated to correct its orientation.

1785632: PDF document index is out of range.

After an upgrade to PDFIUM the transfer of atypical characters from the PDF document to the extracted text is now prevented, and errors are no longer encountered due to these characters.

1781464: OmniPage confidence for handprint always 100% regardless of accuracy.

After an update to the OmniPage recognition engine, the confidence for handprinted text now reflects its true accuracy.

1776441: Missing Kofax.KSMS.Global.dll after upgrade from KTM 6.4.0.x to KTM 7.0

The Kofax.KSMS.Global.dll is no longer missing when upgrading from 6.4.

1774358: In Document Review, when user enters a value and clicks the down arrow, all class names are being displayed.

When a user enters a value in the Class combobox to search for a class and then uses the down arrow to select a class, the full results are no longer displayed.

Instead, the entered value filters the class list based on the entered string as expected.

1774340: Edit Training Document Window Causes Errors

The Edit Training Document window is now displayed as expected each time the window is opened.

Applies To

This fix pack is cumulative and includes the resolved issues released in previous Kofax Transformation Modules 7.0.0 fix packs.

You can apply this fix pack to update any of the following versions:

Kofax Transformation Modules 7.0.0 Fix Pack 1

Kofax Transformation Modules 7.0.0

Files Included

This fix pack includes the following files:

File name | Version
KofaxTransformationModules-7.0.0.2.exe | 7.0.0.2
FoxBase.22.dll | 7.0.0.2
Kofax.KSMS.Global.dll | 7.0.0.2
FoxAdvZoneLoc.22.dll | 7.0.0.2
FoxRecogOmniPage.22.dll | 7.0.0.2
ReadMe-KTM-7.0.0.2.htm | N/A

Install This Fix Pack

Before installing this fix pack, note the following:

Do not remove or attempt to repair Kofax Transformation Modules using the .msp file provided with this fix pack. This can corrupt your installation and cause errors.

You must have full Windows administrative privileges to perform these procedures.

Make sure that Kofax Capture and Kofax Transformation Modules 7.0.0 are installed before applying the fix pack.

Install the fix pack on each client and standalone workstation running Kofax Transformation Modules. You can either run the installation from the .exe file or use the .msp file from the Command Prompt, which also gives you the option to run logging.

Install the Fix Pack with the .exe File

Use the following procedure to install the fix pack using the .exe file.

Close all Kofax Transformation Modules applications and services.

Run KofaxTransformationModules-7.0.0.2.exe to install the fix pack.

When you are notified that the installation process has been successfully completed, click OK to clear the confirmation message.

Install the Fix Pack with the .msp File

Use the following procedure to install the fix pack using the .msp.

Note: An MSP is no longer included with Kofax Transformation Modules.

For Kofax Transformation Modules fix packs, it is possible to extract the MSP from the executable as follows.

KofaxTransformationModules-7.0.0.2.exe /T: /C

In addition to these parameters, you can also use /Q for quiet mode.

The same goes for the Thin Client Server. You can extract the MSP from the executable using these same parameters.

Important: Do not remove or attempt to repair Kofax Transformation Modules using the extracted .msp file. This can corrupt your installation and cause errors.

Perform these steps on each client and workstation running Kofax Transformation Modules:

Start the Command Prompt as an Administrator.

Use the cd command to switch to the folder containing .msp file.

Run the following command:

msiexec /update KofaxTransformationModules-7.0.0.2.msp REINSTALL=ALL REINSTALLMODE=omus PATCHINSTALL=1

To enable logging, add the /L switch to the end of the command. The following command generates verbose logging to C:\KofaxTransformationModules-7.0.0.2.log:

/L*v C:\KofaxTransformationModules-7.0.0.2.log

Remove This Fix Pack

Before removing this Fix Pack, note the following:

You must have full Windows administrative privileges to perform these procedures.

Have access to KofaxTransformationModules-7.0.0 .iso", the original installer program for Kofax Transformation Modules 7.0.0 .

Mount the ISO image or use the network resource.

Use the following procedure to remove the fix pack.

Terminate all running Kofax Transformation Modules applications and services.

In Control Panel, select Programs and Features > View installed updates.

On the list of updates, in the Name column, select the item that corresponds to Kofax Transformation Modules 7.0.0 Fix Pack 2.

Right-click and select Uninstall.

Restart any applications/services that were stopped prior to removing the fix pack.

Log on Account for the System

Be sure that the log on account used to run the services has full Windows administrative privileges for the local system.

Changing the Server Scheduler Timeout Period

To change the Server Scheduler timeout period, do the following:

In the Registry Editor, select the following key:

For x64 operating systems: HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Kofax\Transformation\4.0\Server

For x86 operating systems: HKEY_LOCAL_MACHINE\SOFTWARE\Kofax\Transformation\4.0\Server

Right-click the key and select New > DWORD (32-bit) Value.

In the Name field, enter ExtractionProcessTimeout.

In the Data field, enter the duration of the timeout in minutes. The default is 1440 for 24 hours.

Restart Server Scheduler.